Author: Lin Nei Source: Tutorial Network
Original image
Effect
1.Open the original image
2. Use the “Pen Tool” to outline the path. The path should not be continuous, but divided into four lines
3. Select the “Spot Healing Brush Tool” and adjust the diameter of the current tool to the appropriate size according to the thickness of the rope; then click “Content Awareness” on the property bar,
“Sample all layers”, and create a new transparent layer; the purpose of the latter two is to apply the editing results to the new layer so that
The original image will not be destroyed and the current layer can be modified in real time (the same below).
4. Click the arrow to execute “Stroke Path”, and select “Spot Healing Brush” in the check box (this operation is slightly different from the previous version, cs3/4 is currently
under Tools is the default without having to select the tool again), then OK
5. Look at the effect, well, it’s very good and powerful; but there are still some traces
6. Enlarge the image and fix the imperfections. To modify the details, we use the “Healing Brush Tool” and adjust the diameter to the appropriate size. According to the repair content,
We need to open the “Clone Source” panel to adjust the angle (or size; this time, CS5 adds a reverse function) in the repair target. Click on the panel
Square “Source 1” and check “Show Overlay” where the arrow points, then hold down the alt key to select an area on the edge of the outer fruit, click to select the clone source, this
Since “Show Overlay” is checked, we can see that the clone source is superimposed on the cursor, so that we can observe and adjust its angle very intuitively
and size. Rotate the “angle” shown in the red box clockwise until it is consistent with the angle of the repaired area. After completing these steps, remember to create a new transparent image
layer, and select “Current and Lower Layers” in the sample box of the property bar to apply the editing results to the new layer.
7. Next click “Source 2”, create a new transparent layer, and repair the internal test fruit. The steps are the same as above
, observe the image carefully by zooming in and out, and use the above methods to improve every detail. This is the finished effect
This example is not complex in general, and it is difficult to reflect the power of one of the new features of CS5.
Later, I used shift to draw straight lines (according to the image), and the result was good. If you have time, try to find a “curved” picture. By the way, let’s start using it
It is a smart fill, and the effect is not good, but I found that after executing “Stroke Path>Quick Selection Tool”, the selection can be controlled in the rope area. Compared with this
The former CS3/4 is easier to operate. The tools under the stroke path are not used much, I hope friends who are interested can explore it.
1. Path
2. The effect after executing “Stroke Path>Quick Selection Tool”
Author: Lin Nei Source: Tutorial Network
Original image
Effect
1.Open the original image
2. Use the “Pen Tool” to outline the path. The path should not be continuous, but divided into four lines
3. Select the “Spot Healing Brush Tool” and adjust the diameter of the current tool to the appropriate size according to the thickness of the rope; then click “Content Awareness” on the property bar,
“Sample all layers”, and create a new transparent layer; the purpose of the latter two is to apply the editing results to the new layer so that
The original image will not be destroyed and the current layer can be modified in real time (the same below).
4. Click the arrow to execute “Stroke Path”, and select “Spot Healing Brush” in the check box (this operation is slightly different from the previous version, cs3/4 is currently
under Tools is the default without having to select the tool again), then OK
5. Look at the effect, well, it’s very good and powerful; but there are still some traces
6. Enlarge the image and fix the imperfections. To modify the details, we use the “Healing Brush Tool” and adjust the diameter to the appropriate size. According to the repair content,
We need to open the “Clone Source” panel to adjust the angle (or size; this time, CS5 adds a reverse function) in the repair target. Click on the panel
Square “Source 1” and check “Show Overlay” where the arrow points, then hold down the alt key to select an area on the edge of the outer fruit, click to select the clone source, this
Since “Show Overlay” is checked, we can see that the clone source is superimposed on the cursor, so that we can observe and adjust its angle very intuitively
and size. Rotate the “angle” shown in the red box clockwise until it is consistent with the angle of the repaired area. After completing these steps, remember to create a new transparent image
layer, and select “Current and Lower Layers” in the sample box of the property bar to apply the editing results to the new layer.
7. Next click “Source 2”, create a new transparent layer, and repair the internal test fruit. The steps are the same as above
, observe the image carefully by zooming in and out, and use the above methods to improve every detail. This is the finished effect
This example is not complex in general, and it is difficult to reflect the power of one of the new features of CS5.
Later, I used shift to draw straight lines (according to the image), and the result was good. If you have time, try to find a “curved” picture. By the way, let’s start using it
It is a smart fill, and the effect is not good, but I found that after executing “Stroke Path>Quick Selection Tool”, the selection can be controlled in the rope area. Compared with this
The former CS3/4 is easier to operate. The tools under the stroke path are not used much, I hope friends who are interested can explore it.
1. Path
2. The effect after executing “Stroke Path>Quick Selection Tool”
<!–Collectio
微信扫一扫打赏
支付宝扫一扫打赏
