The most complete beauty treatment tutorial for girls (classic microdermabrasion tutorial) PS steps: 1: Old routine: copy layer screen.width*0.7) {this.resized=true; this.width=screen.width*0.7; this.style.cursor=’hand’; this.alt=’Click here to open new window\nCTRL Mouse wheel to zoom in/out’;}” alt=”The most complete beauty treatment tutorial for MM (classic microdermabrasion tutorial) )” src=”/wp-content/uploads/2024/05/08/yve1bqxn1e4.jpg” tag.php?name=screen” class=”t_tag”>screen.width*0.7) { this.resized=true; this.width=screen.width*0.7; this.alt=’Click here to open new window\nCTRL Mouse wheel to zoom in/out’;}” border=0>
2. Enlarge the picture 
3. Use the lasso tool to select part of the skin next to the big acne
4. Hold down the ctrl alt key and drag the selected skin to the acne with the left mouse button. Note that you can only stick to part of the acne
5. Then select part of the skin from the other side of the acne and stick it on. If the acne is large, you can select several times around the acne 
6. Until all large acne is covered. If you use the stamp tool to repair it, there will be traces after enlarging it. Use the blur tool in the toolbox, intensity 100
7. Apply it to the areas on your face that are not pleasing to the eye. Don’t apply too much, it’s almost done. Otherwise, you will become a rubber person
8. This film is not exposed enough, open the curve 
9. Lighten dark areas
10. Turn on color balance
11. Adjust 
12. Adjust the brightness and contrast
13. The facial color contrast is large, open the optional color
14. Adjustment The proportion of each color. Change the method to absolute 
15. Add a mask and use a brush to paint the areas that need to be clear, with a slightly wider range. Bigger
16. Exit the mask and select reverse
17. Open the color range
18. Use the straw on the left to point the darkest part (such as hair), and adjust the color tolerance to 200 
19. Storage selection
20. Pick any name, I chose 1 
21. Open the channel, you can see the 1 channel just stored, click 
22. Open the fill
23. Click 50% gray
24. Return to the RGB channel and open the loading selection area
25. Load 1 channel
26. Open USM sharpening
27. Press the ctrl H key at the same time to hide the ant line. The sharpening radius should not exceed 1, and the amount should be adjusted until it is clear
28. Deselect using 50% gray in the color range and then sharpen. This will allow you to overdo it naturally. Direct sharpening will be too hard and the contrast will be too great. I’m tired today, so I’ll do this first and continue tomorrow
29. Do the lips again. Enter the mask and select the lips 
30. Exit the mask and select—Reverse
31. Image—Adjustment—Hue/ Saturation
32. Press the ctrl H key at the same time to hide the ant line (remember, I won’t talk about it later), adjust 
33. Cancel the selection. Do the eye light again. Enter the mask and click on the reflective spot of the eyeball 
34. Exit the mask and select – Reverse
35. Filter – Others – Maximum value. This filter can expand the reflective points, and the effect obtained is more natural than the dodge tool in the toolbox that expands the reflective points, and it is also easier to control
36. Adjust the radius, slightly over
37. If you feel the light in your eyes expanding It is rather stiff and can be adjusted with opacity
38. I feel that the left side of MM’s face is a bit overexposed. Use a straw to click a little outside the highlight part of the left face
39. Use the brush tool to reduce the hardness, opacity and flow. Apply the highlights on MM’s face to cover the highlights 
40. After it is done, it will look like this. The color of my monitor is not accurate, so I will just give you a rough guide. If the light is too flat, you can add some lighting effects in the filter, or use the gradient tool. You can edit it later when you are interested. It is very tiring to edit the tutorial. 
Simple, we teach You, profound, share it
<!–Collectio
微信扫一扫打赏
支付宝扫一扫打赏
